Quickboot mac how to#
Quickboot mac install#

These changes are called out in the tables. Note - For NSV version 2.2.0.x and higher, there are certain changes in the menu options. The tables in the following sections describe each parameter setting in the BIOS Setup utility. You might decide to alter these default values if there is a conflict between device settings or to optimize system performance. Note - You can use the Fusion-MPT PCI SCSI BIOS Configuration utility to change the default configuration of your SCSI host adapters.

To access a submenu, select the item so that it is highlighted and press Enter. Items that include submenus begin with a triangle icon. Use the left and right arrow keys to change the options for each setting.Use the up and down arrow keys to move among the settings in each menu.Refer to the Sun Fire V20z and Sun Fire V40z Servers-Server Management Guide, for more information about managing the server remotely.įrom the Main menu screen, you can access other setup screens, such as Security and Power. To access the BIOS Setup utility remotely, you can log in by means of an SSH client. Note - If you are using a USB keyboard, the F2 key might not work properly when entering BIOS Setup unless the F-Lock key is on.ĭuring system boot, you can also press the F12 key to boot the network. To change the system parameters, enter the BIOS Setup utility by pressing the F2 key when prompted, as the system is booting. Changing these parameters is only necessary if you want to change the defaults. When the computer is powered on, it is configured with the values stored in the BIOS ROM by the system BIOS, which gains control at boot time. The Basic Input Output System (BIOS) Setup utility can be used to configure BIOS settings. For information about setting up a network Preboot Execution Environment (PXE) installation, see the Sun Fire V20z and Sun Fire V40z Servers-Linux Operating System Installation Guide. To boot from the default boot device, let the prompt time out and the boot process will continue.įor further information about the BIOS Setup utility, refer to Section 2.4, BIOS Setup Utility. When prompted, you can press the F2 key to enter the BIOS Setup utility or press the F12 key to boot from the network.

Quickboot mac install#

This is normal until after you install an operating system.ģ. Note - If this is the first time you are booting the server, the booting stops and displays a message on the monitor, Operating system not found, and the LCD on the front panel displays the message, OS Booting. There is no separate AC Power switch on the Sun Fire V40z server basic AC power is applied when you plug in a power cord to a power supply. This button provides power to the BIOS, operating system, and drivers. Push and release the platform Power button on the server front panel (see FIGURE 1-4). If you have a Sun Fire V40z server, use this step:Ī.Push and release the platform Power button on the server front panel (see FIGURE 1-1). This switch provides AC power to the SP and basic hardware.ī. Turn on the AC Power switch on the server back panel (see FIGURE 1-2). If you have a Sun Fire V20z server, use these steps:Ī.Power on the server using one of the following two methods, depending on which server type you have: Severe damage to server components will occur if the server is operated without adequate cooling mechanisms.ġ.Ğnsure that an AC power cord is plugged into each power connector on the rear of the server and into an AC power outlet(s).Ģ. See Section 2.4, BIOS Setup Utility for more information.Ĭaution - Do not operate this server without all fans, component heat sinks, air baffles, and the cover installed. USB keyboard support is disabled in the BIOS by default. If you want to configure the server BIOS, you must use a PS/2 keyboard for initial bootup.

Quickboot mac how to#

For information about how to identify which version of the server you have, refer to Section 3.4, Releases of the Sun Fire V20z Serverand Section 4.4, Releases of the Sun Fire V40z Server. The updated release (chassis PN 380-1206) of the server does notship with the packaging insert in the PCI card slots. Do notremove the plastic air-baffle inserts from the PCI slots. You can discard these packaging inserts, which serve as protection during shipping. Note - Before powering on the server for the first time, follow the setup instructions in the Sun Fire V20z and Sun Fire V40z Servers-Installation Guide.Ĭaution - Before you power on a Sun Fire V40z server for the first time, you must remove the packaging inserts from the server’s PCI card slots and CPU card slot to ensure proper airflow and cooling.